耀彩网1、看手动链条是否向下，在将电机固定在主板上。在把链条固定在轮盘和电机底座齿轮连接(一定上紧)在将遥控接线盒与电机连接，试下手柄是否颠倒，如颠倒遥控接收盒侧方有黑色按键，向另一方拨动助即可。

1. Firstly, check if the manual chain is facing downwards before fixing the motor onto the motherboard. After fixing the chain to the wheel and connecting it to the motor base gear (be sure to tighten it), connect the remote control junction box to the motor, and try to check if the handle is reversed. If there is a black button on the side of the remote control receiver box that is reversed, move the assist button towards the other side.

耀彩网2、用尺子量主板和副板的外边看下尺寸是否正确，如正确把轴上在侧板上，注意要先把轴打一条水平线，再用10个钻头打孔50公分，1个一定要直，再用14的镙母焊在轴上，记住要与轴上的孔垂直在焊，一定要焊牢固，再把帘子的片的中心与轴上的孔对齐用10个的钻头打孔一定要垂直(也可以用快丝固定)。

2. Measure the outer edges of the motherboard and sub board with a ruler to see if the dimensions are correct. If the shaft is correctly placed on the side panel, make sure to first draw a horizontal line on the shaft, then use 10 drill bits to drill holes of 50cm, one must be straight, and then use 14 nuts to weld it on the shaft. Remember to weld it perpendicular to the hole on the shaft, be sure to weld it firmly, and then align the center of the first piece of the curtain with the hole on the shaft. Use 10 drill bits to drill holes vertically (or use fast wire to fix it).

3、在将卷帘门帘片穿好两侧用封头封好用拉铆钉拉住(记住开始封各一片封一个)。

3. Seal both sides of the rolling shutter with a sealing head and pull with rivets (remember to start sealing one piece at a time).

耀彩网4、封完后用绳翻过轴把帘子打个孔一头一个用绳拴住，别一端用人拽住，按下手柄的上升键，使轴运行将帘子带上去，镙丝杆把帘子和轴连在一起(水平要拧紧加垫)再把帘子升上去，一定要牢固。

耀彩网4. After sealing, use a rope to flip over the shaft and make a hole on the curtain. Tie one end of the curtain with a rope, and use someone to pull the other end. Press the up button of the handle to move the shaft and bring the curtain up. Use a screw to connect the curtain and shaft together (tighten and pad horizontally), and then lift the curtain up firmly.

5、把轨道的一端开成人字口。

5. Open one end of the track into a zigzag opening.

耀彩网6、把卷帘门帘子调平，上下线定位，左边滑轮是上限位，右边是下限位，(根据现场需要自行调节)。

6. Level the curtain of the rolling shutter door, position the upper and lower lines. The left pulley is the upper limit position, and the right pulley is the lower limit position (adjust according to on-site needs).

本文由济南卷帘门厂友情奉献.更多有关的知识请点击:http://zbfuguang.com耀彩网真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待

This article is a friendly contribution from Jinan Roller Shutter Door Factory. For more information, please click: http://zbfuguang.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned