铝合金卷帘门越来越受到用户的追捧，普遍适用于车库门、商铺门、银行大门、阳台窗等地，铝合金卷帘门好吗？下面一起来来看一下铝合金卷帘门的安装也会存在防火性能是怎样的吧。

Aluminum alloy roller shutter doors are more and more popular with users. They are generally applicable to garage doors, shop doors, bank doors, balcony windows and other places. Is aluminum alloy roller shutter door good? Let's take a look at the fire performance of the installation of aluminum alloy roller shutter doors.

1.铝合金卷帘相邻帘板串接后应转动灵活，摆动90°不应脱落。铝合金卷帘的帘板装配完毕后应平直，不应有孔洞或缝隙。铝合金卷帘板两端挡板或防窜机构应装配牢固，卷帘运行时，相邻帘板窜动量不应大于2mm。无机纤维复合铝合金卷帘面两端应安装防风钩。无机纤维复合铝合金卷帘面应通过固定件与卷轴相连。

1. The aluminum alloy roller shutter shall rotate flexibly after the adjacent curtain plates are connected in series, and shall swing 90 ° without falling off. The curtain plate of aluminum alloy roller shutter shall be straight after assembly without holes or gaps. The baffles or anti channeling mechanisms at both ends of the aluminum alloy roller shutter shall be firmly assembled. When the roller shutter operates, the channeling amount of the adjacent shutter shall not be greater than 2mm. Wind hooks shall be installed at both ends of inorganic fiber composite aluminum alloy roller blind. The inorganic fiber composite aluminum alloy roller blind shall be connected with the roller shaft through a fixed piece.

2.铝合金卷帘板或帘面嵌入导轨的深度应符合规范规定，卷帘安装后不应变形。导轨顶部应成圆弧形，其长度应保证卷帘正常运行。导轨的滑动面应光滑、平直。帘片或帘面、滚轮在导轨内运行时应平稳顺畅，不应有碰撞和冲击现象。

2. The depth of aluminum alloy roller shutter plate or curtain surface embedded in the guide rail shall meet the specifications, and the roller shutter shall not be deformed after installation. The top of the guide rail shall be in arc shape, and its length shall ensure the normal operation of the roller shutter. The sliding surface of the guide rail shall be smooth and straight. The curtain sheet or curtain surface and roller shall run smoothly in the guide rail without collision and impact.

单帘面卷帘的两根导轨应互相平行，双帘面卷帘不同帘面的导轨也应互相平行，其平行度误差均不应大于5mm。卷帘的导轨安装后相对于基础面的垂直度误差不应大于1.5mm/m，全长不应大于20mm。

The two guide rails of single curtain roller shutter shall be parallel to each other, and the guide rails of different curtain surfaces of double curtain roller shutter shall also be parallel to each other, and the parallelism error shall not be greater than 5mm. After the installation of the guide rail of the roller shutter, the perpendicularity error relative to the foundation surface shall not be greater than 1.5mm/m, and the total length shall not be greater than 20mm.

卷帘的防烟装置与帘面应均匀紧密贴合，其贴合面长度不应小于导轨长度的80%。铝合金卷帘的导轨应安装在建筑结构上，并应采用预埋螺栓、焊接或膨胀螺栓连接。导轨安装应牢固，固定点间距应为600mm～1000mm。

The smoke prevention device of the roller shutter and the curtain surface shall be uniformly and closely bonded, and the length of the bonding surface shall not be less than 80% of the length of the guide rail. The guide rail of aluminum alloy roller shutter shall be installed on the building structure and shall be connected by embedded bolts, welding or expansion bolts. The guide rail shall be firmly installed, and the distance between fixed points shall be 600mm ~ 1000mm.

3.铝合金卷帘座板与地面应平行，接触应均匀。座板与帘板或帘面之间的连接应牢固。无机复合铝合金卷帘的座板应保证帘面下降顺畅，并应保证帘面具有适当悬垂度。

3. The aluminum alloy roller blind base plate shall be parallel to the ground and the contact shall be uniform. The connection between base plate and curtain plate or curtain surface shall be firm. The base plate of inorganic composite aluminum alloy roller shutter shall ensure smooth lowering of the curtain surface and proper sag of the curtain surface.

4.门楣安装应牢固，固定点间距应为600mm～1000mm。门楣内的防烟装置与卷帘板或帘面表面应均匀紧密贴合，其贴合面长度不应小于门楣长度的80%，非贴合部位的缝隙不应大于2mm。

4. The lintel shall be firmly installed, and the spacing between fixing points shall be 600mm ~ 1000mm. The smoke prevention device in the lintel shall be uniformly and closely bonded with the roller shutter plate or curtain surface, and the length of the bonding surface shall not be less than 80% of the lintel length, and the gap at the non bonding part shall not be more than 2mm.

5.卷轴与支架板应牢固地安装在混凝土结构或预埋钢件上。卷轴在正常使用时的挠度应小于卷轴的1/400。

5. The reel and support plate shall be firmly installed on the concrete structure or embedded steel parts. The deflection of the reel in normal use shall be less than 1 / 400 of the reel.

6.济南卷帘门厂认为卷门机应按产品说明书要求安装，且应牢固可靠。卷门机应设有手动拉链和手动速放装置，其安装位置应便于操作，并应有明显标志。手动拉链和手动速放装置不应加锁，且应采用不燃或难燃材料制作。

6. Jinan rolling door factory believes that the rolling door machine shall be installed according to the requirements of the product manual and shall be firm and reliable. The door rolling machine shall be equipped with manual zipper and manual quick release device. The installation position shall be convenient for operation and shall have obvious marks. Manual zippers and manual quick release devices shall not be locked and shall be made of non combustible or non combustible materials.

7.防护罩尺寸的大小应与铝合金卷帘洞口宽度和卷帘卷起后的尺寸相适应，并应保证卷帘卷满后与防护罩仍保持一定的距离，不应相互碰撞。防护罩靠近卷门机处，应留有检修口。防护罩的耐火性能应与铝合金卷帘相同。

7. The size of the protective cover shall be compatible with the opening width of the aluminum alloy roller shutter and the size after the roller shutter is rolled up, and it shall be ensured that the roller shutter still keeps a certain distance from the protective cover after being rolled up, and shall not collide with each other. An access hole shall be reserved at the place where the protective cover is close to the door rolling machine. The fire resistance of the protective cover shall be the same as that of the aluminum alloy roller shutter.

此外铝合金卷帘门具有很好的抗老化功能，且耐腐蚀性强，同时还具有出色的抗击打性能，所以它被广泛安装，您有定制需求就来我们网站http://zbfuguang.com咨询吧。

In addition, the aluminum alloy roller shutter door has good anti-aging function, strong corrosion resistance, and excellent anti-corrosion performance, so it is widely installed. If you have customized needs, please come to our website http://zbfuguang.com Consult.