在感应玻璃门日常使用的过程中，常见的故障就是突然打不开了或者突然关不上了？遇到这种故障你知道如何办吗？今天小编就根据平常维修感应玻璃门故障的经验为大家总结了一些维修方法。
In the process of daily use of induction glass doors, the common fault is that they suddenly fail to open or close? Do you know how to deal with this kind of trouble? Today, Xiaobian summarized some maintenance methods for you based on the experience of ordinary maintenance of induction glass door faults.
一、检查是否是感应玻璃门防夹功能在作怪，导致感应玻璃门打不开。
1、 Check whether the anti pinch function of the induction glass door is causing trouble, resulting in the non opening of the induction glass door.
感应玻璃门机具有防夹功能，遇到障碍或感应玻璃门碰撞会导致感应玻璃门不能正常打开，在达到三次时，感应玻璃门将会停止运行，门扇会停止开门或关闭，遇到这种问题只需将门扇推完全打开状态即可恢复。
The induction glass door machine has the anti pinch function. When encountering obstacles or the collision of the induction glass door, the induction glass door cannot be opened normally. When it reaches three times, the induction glass door will stop running, and the door leaf will stop opening or closing. In case of this problem, just push the door leaf to the fully open state to recover.
二、感应玻璃门内部皮带装反，导致感应玻璃门关不上。
2、 The inner belt of the induction glass door is installed reversely, which causes the induction glass door to fail to close.
在人通行时，感应玻璃门关闭反而走开时感应玻璃门打开并且打开后不再关闭。遇到这种情况大家都会认为这是关不上打不开了。这个问题是因为感应玻璃门在安装或维修时因为技术人员不，把动力皮带装反了导致。解决方法是一、调换皮带上下扣连接，三、控制器故障导致感应玻璃门出现打不开和关不上。
When people pass, the sensing glass door closes, but when they walk away, the sensing glass door opens and does not close after opening. In this case, everyone will think that it can't be closed or opened. This problem is caused by the reverse installation of the power belt during the installation or maintenance of the induction glass door due to the unprofessional technicians. The solution is: first, replace the upper and lower buckle connections of the belt; third, the controller failure causes the induction glass door to fail to open and close.
遇到这种故障需要调试控制器，如调试不能使其恢复正常，就需要更换控制器了。所以建议大家在进行维护安装时应找人员，不可因小失大。
In case of such failure, the controller needs to be debugged. If the debugging cannot make it return to normal, the controller needs to be replaced. Therefore, it is suggested that you should find professionals when carrying out maintenance and installation, and you should not lose too much for too little.

四、感应玻璃门敞开或关闭的情况下接通电源无反应
4、 When the induction glass door is open or closed, there is no response when the power is turned on
这情况需要到现场进行检测，因为出现这个问题的情况比较多，比如虽然插上电源但没有供电也有可能是控制器死机等原因造成。门道佰分佰技术人员可现场对此问题进行检测并针对性解决问题。
This situation needs to be detected on site, because there are many cases of this problem. For example, although the power is plugged in, there is no power supply, which may also be caused by the controller crash and other reasons. Doorway technicians can detect and solve this problem on site.
五、遥控器问题，导致感应玻璃门打不开。
5、 There is a problem with the remote control, causing the induction glass door to fail to open.
因感应玻璃门遥控器问题导致，用要看解锁即可。
Due to the problem of the remote control of the induction glass door, you can use it only by unlocking it.
六、感应玻璃门有关门动作，但无法关闭。
6、 The induction glass door has a closing action, but it cannot be closed.
济南卷帘门厂认为此种原因是感应器有开门信号输入，也就是感应器感应范围内有干扰物存在，比如：太阳光直射、有活动的物体、有不稳定光源等。可以通过断掉感应器信号线来测试是否因为感应器的干扰信号引起感应玻璃门无法关闭。
Jinan rolling shutter door factory believes that this reason is that the sensor has a door opening signal input, that is, there are interferences within the sensing range of the sensor, such as direct sunlight, moving objects, unstable light sources, etc. You can test whether the inductive glass door cannot be closed due to the interference signal of the sensor by cutting off the sensor signal line.
感应玻璃门打不开关不上可能还会有其他问题导致，这些问题需现场检测维修。还有其他问题就来关注我们网站http://zbfuguang.com寻找解答吧。
There may be other problems caused by the non opening and closing of the induction glass door, which need on-site inspection and maintenance. If you have other questions, please pay attention to our website http://zbfuguang.com Find the answer.