随着不锈钢卷帘门的生产和安装周期大大缩短，工作效率大大提高。同时，对不锈钢卷帘门安装后的调试和验收尤为重要。不锈钢卷帘门的主要调试有以下几个部分。

With the production and installation cycle of stainless steel rolling shutter door greatly shortened, the work efficiency has been greatly improved. At the same time, the commissioning and acceptance of the stainless steel rolling shutter door after installation is particularly important. The main commissioning of stainless steel rolling shutter door includes the following parts.

上下限位调试检测：门体静止时，按下向上按钮，门体向上运行。缓冲完全停止后，判断起升高度是否满足用户要求。如果不符合要求，重新调试；之后按下下降按钮，待门体完全停止下落后，观察门体末端的停止位置是否自然、端正。

Upper and lower limit commissioning detection: when the door body is stationary, press the up button and the door body will run upward. After the buffer stops completely, judge whether the lifting height meets the user's requirements. If it does not meet the requirements, re commissioning; Then press the down button. After the door body completely stops falling, observe whether the stop position at the end of the door body is natural and correct.

急停按钮性能检测：在门运行过程中，按下急停按钮，观察门是否立即停止。如果仍能正常运行，请检查急停按钮是否失灵或损坏。

Performance test of emergency stop button: during the operation of the door, press the emergency stop button and observe whether the door stops immediately. If it still works normally, please check whether the emergency stop button fails or is damaged.

红外防砸性能调试：在门体下落过程中，切断红外拍摄系统，看门体是否会及时反弹上升。测试过程中注意自身，防止红外系统故障造成伤害。

Infrared anti smashing performance debugging: during the falling process of the door body, cut off the infrared shooting system to see whether the door body will rebound and rise in time. Pay attention to your own safety during the test to prevent injury caused by infrared system failure.

此外，可用外观检查法检查所有紧固件是否松紧。有外漏的零件表面必须进行防锈处理，涂层和涂层必须均匀。组件的组装和拼接不得错位。

In addition, all fasteners can be checked for tightness by visual inspection. The surface of parts with external leakage must be subject to rust prevention treatment, and the coating and coating must be uniform. The assembly and splicing of components shall not be misplaced.

济南卷帘门厂厂家提醒您，焊接处要牢固，外观要平整，不能存在漏焊、夹渣现象，不能存在表面缺陷（锤痕、空洞、碰伤、毛刺喷质、凹陷、划伤、变形、ETC。）

The manufacturer of Jinan rolling shutter door factory reminds you that the welding position should be firm, the appearance should be flat, and there should be no missing welding, slag inclusion, and surface defects (hammer marks, holes, bumps, burrs, spraying, dents, scratches, deformation, etc.)

窗帘串联后，转动要灵活，窗帘两端的侧扣要牢固；窗帘之间的连接应可靠，运行时应无脱钩、无间隙、无危险。导轨和端座安装要牢固。卷帘门锁可安装在距地面约1m处或座杆上，卷帘窗锁装置组装在座杆上，启闭应灵活可靠。

After the curtain is connected in series, the rotation shall be flexible, and the side buckles at both ends of the curtain shall be firm; The connection between curtains shall be reliable, and there shall be no decoupling, clearance and danger during operation. Guide rail and end seat shall be firmly installed. The rolling shutter door lock can be installed about 1m from the ground or on the seat rod. The rolling shutter window lock device is assembled on the seat rod, and the opening and closing shall be flexible and reliable.

以上就是对这篇文章的内容，看完这篇文章，希望对您有所帮助，我们网站还有很多的相关内容的详细描述，如果你想了解更多，欢迎关注我们的网站zbfuguang.com。

The above is the content of this article. After reading this article, I hope it will help you. Our website also has a lot of detailed descriptions of relevant content. If you want to know more, please follow our website zbfuguang.com。