在快速门系列产品中，快速卷帘门对安装要求是非常高的，需要结合实际门洞情况来定安装方案，结合快速卷帘门的安装示意图，济南卷帘门厂来讲解一下快速门在安装中需要注意的各个要点。

Among the fast shutter series products, the fast shutter door has very high installation requirements, so the installation scheme needs to be determined according to the actual door opening situation. In combination with the installation diagram of the fast shutter door, Jinan Rolling Door Factory will explain the key points that need to be paid attention to in the installation of the fast shutter door.

1、安装快速门的门洞上方需要一定的空间来安装快速卷帘门机头，快速卷帘门的机头是一个比较规则的长方体，通常情况下机头下方会预留200mm高度的预留空间，所以机头的上方空间为A+200mm，机头的高度A的大小会受到门洞高度的影响，门洞高度越大机头的高度A也会越大，如果门洞上方空间较小，可以通过加装一块门板，将预留的200mm空间省略掉。

1. A certain space is required above the door opening where the fast shutter door is installed to install the head of the fast shutter door. The head of the fast shutter door is a regular cuboid. Normally, a space of 200mm is reserved below the head, so the space above the head is A+200mm. The height A of the head will be affected by the height of the door opening. The higher the door opening is, the higher the head height A will be. If the space above the door opening is small, The reserved 200mm space can be omitted by adding a door panel.

也可以让机头吃一部分洞口高度，当然须加装一块门板，这样在不于门洞会留有缝隙;机头的厚度，图中所示的B的数值，B的大小也会根据门洞大小有相应的尺寸大小，通常情况下机头厚度不会对安装造成影响，特别的情况下需要具体注意测量;机头的宽度，机头的宽度是大于门洞的宽度的，如果门洞的墙面不平整，要注意机头宽的安装要求为：门洞宽度+立柱跨度*2+100mm。

You can also let the handpiece eat part of the hole height. Of course, a door panel must be installed to avoid gaps in the door opening; The thickness of the machine head, the value of B shown in the figure, and the size of B will also have a corresponding size according to the size of the door opening. Generally, the thickness of the machine head will not affect the installation, and special attention should be paid to the measurement under special circumstances; The width of the handpiece, the width of the handpiece is greater than the width of the door opening. If the wall of the door opening is uneven, pay attention to the installation requirements of the handpiece width: door opening width+column span * 2+100mm.

2、门洞宽度方面需要注意的是，门洞宽度并不是快速卷帘门的安装宽度，门洞宽度通常是开启宽度，而安装宽度为：开启宽度+立柱宽度*2，立柱宽度为图中所示C的数值，立柱宽度的大小也受到门洞宽度的影响。如果门洞是在一个平整的墙面上，只需考虑墙体的坚固性即可，通常都能满足快速卷帘门安装宽度要求。

2. In terms of the door opening width, it should be noted that the door opening width is not the installation width of the quick roll up door. The door opening width is usually the opening width, while the installation width is: opening width+column width * 2. The column width is the value of C shown in the figure. The column width is also affected by the door opening width. If the door opening is on a flat wall, just consider the firmness of the wall, which can generally meet the requirements for the installation width of the fast rolling shutter door.

在快速卷帘门安装的时候，除了需要着重注意以上两点外，还需要注意地面的水平性、门洞上下宽度是否一致、门洞两次墙面是否在一个水平面上等问题。

In addition to the above two points, attention should be paid to the levelness of the ground, whether the upper and lower widths of the door openings are consistent, and whether the two walls of the door openings are on the same horizontal plane.

快速卷帘门不同于普通卷帘门，由于智能化成都较高，好能有正规的专门的快速卷帘门厂家的技术人员现场指挥安装。您可以来我们网站http://zbfuguang.com咨询看看！

The quick rolling shutter door is different from the ordinary rolling shutter door. Due to the high intelligence of Chengdu, it is good to have the technicians of the formal and specialized fast rolling shutter door manufacturer to direct the installation on site. You can come to our website http://zbfuguang.com Consult!