卷帘门是现在许多大型或者门面所需要安装的一种门，收缩方便，并且节省空间。下面来和济南卷帘门厂小编一起看看卷帘门安装的相关详细步骤说明吧。

Roller shutter door is a kind of door that needs to be installed in many large shopping malls or facades. It is convenient to shrink and saves space. Let's take a look at the detailed steps related to the installation of the rolling shutter door with the small editor of Jinan rolling shutter door factory.

步骤一:做好准备

Step 1: get ready

1.材料:专用夹具、刮刀、粉丝袋、冲击电钻、手电钻、电焊机、切割机、螺丝刀、锤子、线坠、水平尺等。

1. Materials: special fixture, scraper, vermicelli bag, impact electric drill, hand electric drill, electric welding machine, cutting machine, screwdriver, hammer, plumb bob, level ruler, etc.

2.工具:柱、上盖、卷轴、刀片和导轨。

2. Tools: center column, upper cover, reel, blade and guide rail.

温馨提示:以上材料都是必备工具，不能少于一个。只有他们准备充分，我们才能开始施工。

Warm tip: the above materials are all necessary tools, and there should be no less than one. Only when they are fully prepared can we start the construction.

步骤2:开始安装卷帘门

Step 2: start installation of roller shutter door

1、确定安装卷帘门的位置，用落线、水平仪等工具进行标记，找出水平线和垂直线。

1. Determine the installation position of the roller shutter door, mark with tools such as falling line and level, and find out the horizontal line and vertical line.

2.根据定位划线开始安装卷帘门框架。

2. Start to install the roller shutter frame according to the positioning line.

3.按照卷帘门机手册中说明的方法步骤和注意事项安装卷帘门机。

3. Install the roller shutter door machine according to the method steps and precautions described in the roller shutter door machine manual.

4.将组装好的卷帘门体固定好，然后将限位器安装在正确的位置，试运行。

4. Fix the assembled roller shutter door, and then install the stopper at the correct position for trial operation.

5.安装滑道、手动机构和包装箱。

5. Install the slide, manual mechanism and packing box.

步骤3:检查结果

Step 3: check the results

1、调试和运行，确保各项功能和设备运行良好。

1. Commissioning and operation to ensure that all functions and equipment operate well.

2.一切安装检查完毕后，即使卷帘门安装完毕，也能正常使用。

2. After all installation and inspection, the roller shutter can be used normally even after installation.

此外来看看卷帘门故障处理方法：

Here's how to deal with the fault of roller shutter door:

1.电机不移动或低速旋转。这种故障通常是由断路、电机烧毁、停止按钮未复位、限位开关动作、重载等引起的。

1. The motor does not move or rotates at low speed. This fault is usually caused by open circuit, motor burning, stop button not reset, limit switch action, heavy load, etc.

处理方法:检查线路并连接；更换烧毁的电机；更换按钮或按几次；拨动限位开关滑块，使其与微动开关触点分离，并调整微动开关位置；检查机械部件有无卡涩，如果有，则卡涩并障碍物。

Treatment method: check the line and connect it; Replace the burnt motor; Change the button or press it several times; Toggle the limit switch slider to separate it from the microswitch contact and adjust the position of the microswitch; Check whether the mechanical parts are jammed. If so, remove the jamming and remove the obstacles.

2.控制故障的位置及原因:继电器(接触器)接触卡死，行程微动开关故障或接触板变形，滑块定位螺钉松动，背板螺钉松动，使背板移位，使滑块或螺母不能随螺杆转动而移动，限位器传动齿轮损坏，按钮上下键卡死。

2. Position and cause of control fault: the relay (contactor) is stuck in contact, the travel micro switch is faulty or the contact plate is deformed, the positioning screw of the slider is loose, the screw of the back plate is loose, and the back plate is displaced, so that the slider or nut cannot move with the rotation of the screw, the transmission gear of the stopper is damaged, and the up and down keys of the button are stuck.

处理方法:更换继电器(接触器)；更换微动开关或触点；拧紧滑块螺丝，复位靠板；更换限制器的传动齿轮；更换按钮。

Treatment method: replace the relay (contactor); Replace the microswitch or contact; Tighten the slider screw and reset the backup plate; Replace the transmission gear of the limiter; Replace the button.

3.手拉链不动。故障原因:圆环链堵塞十字槽；棘爪没有分离棘轮；压链器卡住了。

3. The hand zipper does not move. Fault cause: the ring chain blocks the cross groove; The pawl does not separate the ratchet wheel; The chain presser is stuck.

处理方法:理顺环链；调节棘爪与压链架相对位置；更换或润滑销轴。

Treatment method: straighten out the chain; Adjust the relative position of the pawl and the chain pressing frame; Replace or lubricate the pin shaft.

以上就是卷帘门的安装步骤，从上述文章我们可以看出，平时使用权力门的时候也要小心谨慎，要是发生了故障必须及时报修，这样才能够减少不必要的经济损失。关注我们http://zbfuguang.com了解更多！

The above is the installation steps of the roller shutter door. From the above article, we can see that we should be careful when using the power door at ordinary times. In case of failure, we must report for repair in time, so as to reduce unnecessary economic losses. Follow us http://zbfuguang.com Learn more!