耀彩网

欢迎光临济南市天桥区昌达卷帘门加工部网站!

联系我们 收藏本站 在线留言

新闻资讯

首页>>新闻资讯不锈钢卷帘门维修中的调试步骤
新闻资讯
联系我们
济南市天桥区昌达卷帘门加工部

联系人:刘经理

电话:耀彩网15953131568

网址:http://zbfuguang.com

地址:济南市天桥区金牛建材市场

不锈钢卷帘门维修中的调试步骤

来源:http://zbfuguang.com 日期:2022-06-28 发布人:
不锈钢卷帘门出现故障后,我们要知道它是在哪里损坏的,所以我们需要从故障上进行检查。调试是一种方便有效的方法。下面我们一起来看看卷帘门维修中的调试步骤。
After the stainless steel roller shutter door breaks down, we need to know where it is damaged, so we need to check from the fault. Debugging is a convenient and effective method. Let's take a look at the debugging steps in the maintenance of rolling shutter door.
1、机电更换完成后,检查线及滞流机构无问题,卷帘门下无倒退,门下禁止迟滞。确认后,开始调试和调试限制。
1. After the electromechanical replacement is completed, check that the line and the stagnation mechanism are free of problems, there is no reverse under the roller shutter door, and no hysteresis is allowed under the door. After confirmation, start commissioning and commissioning limitation.
2、不锈钢卷帘门限位机构显示在机电外壳上,称为限位丝杠套滑块式。
2. The threshold mechanism of stainless steel roller shutter is displayed on the electromechanical shell, which is called limit screw sleeve sliding block type.
3、试车前,先抓住限位机构上的锁紧螺丝,然后用手拉动链条,使窗帘离天空约1米。先试一下“上”、“停”、“下”按钮,看不锈钢卷帘门的升降是否灵巧可靠。如果发生变形,可以将窗帘抬起或移开到某个位置。然后,拨动限位螺丝,调整并触摸微动开关滚轮,听到“咔哒”一声,拧紧张紧螺丝。
3. Before commissioning, first grasp the locking screw on the limit mechanism, and then pull the chain by hand to make the curtain about 1m away from the sky. First try the "up", "stop" and "down" buttons to see if the stainless steel roller shutter door is flexible and reliable. In case of deformation, the curtain can be lifted or moved to a certain position. Then, turn the limit screw, adjust and touch the microswitch roller, hear a "click", and tighten the tensioning screw.
4、经过多次调试,当限位到位后,用力拧紧锁紧螺钉。
4. After many times of debugging, when the limit is in place, tighten the locking screw.
济南卷帘门厂
此外济南卷帘门厂认为在进行不锈钢卷帘门维修中应注意检查其电源和不锈钢控制箱,如出现损坏可重新设置或更换。当不锈钢卷帘门出现关不严或是开不完全的情况时,可以重新调整卷帘门的行程开关位置然后检查其门体是否正常。让不锈钢卷帘门体单向运行,从而检查其行程开关及行程开关接线。
In addition, Jinan rolling shutter factory believes that the power supply and stainless steel control box should be checked during the maintenance of stainless steel rolling shutter doors, and can be reset or replaced in case of damage. When the stainless steel roller shutter door is not closed tightly or opened completely, the travel switch position of the roller shutter door can be readjusted, and then check whether the door body is normal. Let the stainless steel roller shutter door body run in one direction, so as to check its travel switch and travel switch wiring.
如果不锈钢卷帘门电机正常动作,但门体不运行,为主要的问题应该是帘片脱扣、卡死等原因,在对卷帘门维修时可以坚固五金件和调节帘片位置,如遇卷帘门体未关紧就自动反向关门或是开门,可以在卷帘门维修时增加其负载力。
If the stainless steel rolling shutter door motor operates normally, but the door body does not operate, the main problem should be that the shutter is tripped, stuck, etc. during the maintenance of the rolling shutter door, the hardware can be strengthened and the position of the shutter can be adjusted. If the rolling shutter door body is not closed tightly, it will automatically close or open the door in reverse, and its load force can be increased during the maintenance of the rolling shutter door.
以上就是问题解答的相关内容了,希望能够帮助到大家,如对这一问题还存在任何疑问,都欢迎关注我们网站http://zbfuguang.com并咨询我们的工作人员,将竭诚为您服务。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://zbfuguang.com And consult our staff, will serve you wholeheartedly.

阅读/ Recommended reading

快速卷帘门是由电机转动带动门帘上下移动达到开门关门的,而电机是由独立的控制系统来控制的,门的开门高度,关门高度已经开关门的速度都是可以根据需求设置的,快速卷帘门也是属于自动化设备中...

卷闸门在安装时要注意什么? 2024-02-27
自动门水晶卷帘门安装方法介绍 2024-02-23
电动卷帘门常见的故障及维修方法 2024-02-21
电动卷帘门的快速保养与维护 2024-02-10

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

  • 宏顺卷帘门